MITSUBISHI ESA30EH-25 Q-ton Air to water
Q-ton offers excellent performance and environmental benefits in various applications and is extremely energy efficient, resulting in large reductions in both energy and carbon emissions. Q-ton uses the safe and highly efficient CO2 as a refrigerant, which is environmentally friendly as it is a natural gas and does not cause harmful ecological effects compared to other products that use standard refrigerants. In addition, the Q-ton provides a constant supply of hot water from 60°C to 90°C and maintains full performance at low ambient temperature, thus having the added advantage of not requiring an external heating source resulting in reduced installation time and cost.
| MITSUBISHI MODEL |
ESA30EH-25 |
| MITSUBISHI POWER SUPPLY |
Three-phase 380 V +-5%,400+-5%,415+-5%,50/60Hz |
| RUN UNTIL COMPLETE (In the intermediate zone)*1(MITSUBISHI) |
| Heating performance |
| Amount of water |
| Power consumption |
| COP |
|
|
|
| RUN UNTIL COMPLETE (In the cold zone)*2(MITSUBISHI) |
| Heating performance |
| Amount of water |
| Power consumption |
| COP |
|
|
|
| SOUND OPERATING PRESSURE (IN THE INTERMEDIATE ZONE )*1,3 |
dB(A) |
58 |
| VOLUME LEVEL OPERATION (IN THE INTERMEDIATE ZONE )*1 |
dB(A) |
70 |
| EXTERNAL DIMENSIONS
MITSUBISHI
|
|
|
| 1690 |
| 1350 |
| 720+35(Water pipe connection ) |
|
| MITSUBISHI Unit weight |
kg |
375(During operation 385) |
| MITSUBISHI Color |
White stucco (approx. 4.2 Y 7.5/1.1 ) |
| COMPRESSOR
(MITSUBISHI)
|
| Type x pcs. |
| Nominal performance |
|
|
| Inverter hermetic compressor x 1 |
| 6.40 |
|
| COOLANT LUBRICANT (MITSUBISHI) |
|
|
|
| Winding chamber resistance (MITSUBISHI) |
w |
20 |
| Antifreeze resistance
(MITSUBISHI)
|
| For water pipe |
| For condensate basin |
| For drain pipe |
|
|
|
| ALTERNATIVE HEAT ,AIR SIDE(MITSUBISHI) |
straight fin type copper tube |
| ALTERNATIVE HEAT ,WATER SIDE(gas cooler)(MITSUBISHI) |
|
|
| Copper pipe coil, indirect heat exchanger |
| 10 |
|
| Fan(MITSUBISHI) |
| Type |
| Yield x pc. |
| air supply |
| External static pressure |
|
|
| Axial flow type (direct coupling engine) x2 |
| 383×2 |
| 260 |
| 50 |
|
| CIRCULATOR(MITSUBISHI) |
| Type x Performance |
| Materials in contact with water |
| Circulator column height |
|
|
| Spiral type inverter pump without self-priming x 100w |
| pps |
| 5m(49kPa) @17L/min |
|
| USE TEMPERATURE RANGE(MITSUBISHI) |
| Outside air temperature |
| Water inlet temperature |
| Hot water outlet temperature |
|
|
| -25 to 43 |
| Completion 5-35, heating 35-63 |
| 60-90 |
|
| WATER PRESSURE RANGE (MITSUBISHI) |
kpa |
500 or lower (maintain the water pressure of 0k Pa at the water heater inlet of the heat pump ) |
| Defrosting(MITSUBISHI) |
hot gas type |
| Anti-vibration and soundproof devices(MITSUBISHI) |
Compressor mounted on a rubber anti-vibration base and wrapped with sound insulation |
| Protection arrangements
(MITSUBISHI)
|
High pressure switch, protection against strong currents, power supply transistor overheat protection and abnormal high pressure protection |
| Pipe connection
(MITSUBISHI)
|
| Feed water inlet |
| Hot water outlet |
| Drainage water outlet |
|
| Rc3/4 [copper 20A]*4 |
| Rc3/4 [copper 20A]*4 |
| Rc3/4 [copper 20A]*4 |
|
| Electrical wiring
(MITSUBISHI)
|
| Leakage relay |
| Power cord size |
| Safety switch |
| Ground wire size |
| Control cable size |
|
| 30A,30mA,0,1 sec |
| 8mm2x4(Length 70m) |
| Rated current 30A, switch capacity 30A |
| M6 |
| Shield wire 0.3mm2 x 2 conductors(MVVS) |
|
| Design pressure (MITSUBISHI) |
MPa |
High Pressure -14/High Pressure -8,5 |
| IP code (MITSUBISHI) |
IP24 |
